[7]

+ [ Induction card 1] toot, toot

+ [ Proximity card 2] toot, toot

+……

+ [ Induction card n] toot, toot

+ [*] Toot complete delete card

5.4.3       delete all the cards have been set:

Please use the restore factory settings mode

5.4.4.       After deleting their valid card PIN also be deleted

5.5           Exit Programming:

[*] Toot

5.6        Set to open the door proximity cards:

5.6.1       card or password mode:

[1] + [0] beeps (default)

5.6.2       Card + PIN mode:

[1] + [1] beeps

5.7.        Password

5.7.1       "Card or Password" mode password:

It refers to the personal password (valid up to each card within the 500 individuals passwords), and 1 general password

5.7.2      Close modify personal password function:

[1] + [2] beeps (default)

5.7.3       open modify personal password function:

[1] + [3] beeps

5.7.4.       Modify PIN: non-programmed state

[ # ] Toot

+ [ Read proximity cards ] toot, toot

+ [ Input . 4 Ihara password ] (default 0000 ) toot

+ [ Enter . 4 -digit password ]

+ [ Re-enter . 4 -digit password ] toot;

5.7.5.      Modify common password:

[3] + [4 -bit general purpose password ] (default 1234 )

When generic password or PIN to 0000 when, under the "Card or Password" mode, the password is invalid

5.8        Set unlock time:

[2]+[TT]。

TT represents unlocking time, in seconds, such as time of unlocking . 3 seconds, then TT = 03 ;

5.9        Set tamper alarm function:

. 5.9.1       Close tamper alarm: [4] + [0]

5.9.2       Open tamper alarm: [4] + [1]

5.10        detecting Magnetic unlocking setting state:

. 5.10.1        detecting the closed state of the door sensor unlocked: [6] + [0]

(Valid command lock)

5.10.2.        Detects the open state of the door sensor unlocking [6] + [1]

( "Effective instruction + Magnetic closed" unlock)

This feature can be used for multi-door interlock.

5.11     Set Magnetic Alarm Status:

5.11.1    Close door sensor alarm function: [8] + [0]

. 5.11.2    open door sensor alarm function: [8] + [1]

After opening this function, when the normally open or not closed, or the door is not opened by the controller, the controller will continuously sounding a beep beep alarm;

5.12        Set the alarm delay time:

[82] + [TT] . TT represents the alarm delay time, in seconds, such as alarm delay time . 3 seconds, then TT = 03

Alarm Delay: blocking TT seconds after the door (door sensor) has not been closed, the alarm, the alarm was released until the door is closed

This instruction takes and an open door sensor alarm function used simultaneously

6.         Restore factory settings:

[86] toot, toot toot, 5 seconds after the beep beep, the controller back to the factory setting state

7.         How to use:

7.1        card or password mode:

7.1.1.       Time password interval should be less than 2 seconds

7.1.2.       Not finished . 4 when the password input position, press the [*] key, cancel the password

7.2        card with a personal password to open the door

7.2.1.       [Read valid card beep] + [PIN] to open the door

7.2.2.       Enter the PIN less than 4 position, the press [*] key, you can directly enter the correct password

8.           forced to restore the factory programming password:

8.1.           Remove the controller

8.2.           The J2 of feet short answer it after the release, the controller toot, toot can.

9.           Frequently Asked Questions:

สอนแพ๊กแบตรถไฟฟ้า,สอนซ่อมรถไฟฟ้า,รับทำโครงงาน,เปิดสอนArduino,ขายsensor,รับทำโปรเจค,รับทำproject,รับทำโปรเจคจบ,รับเขียนโปรแกรมทุกชนิด,รับทำไมโคร,pic16f877,mcs51,avr,arduino,sensor,loadcell,GSM,GPRS,sim300,sim900,internet control,hardware,electronic,programming,control,controller,robot,controlrobot,bluetooth control,hardware control,delphi,AGV Robot,trackking line,servomotor,steppingmotor,encoder,temp control,PID,speed control,displayboard,moving board,ป้ายไฟวิ่ง,ป้ายไฟ,ป้ายตัวอักษรวิ่ง

089-765-42-37 electhailand@gmail.com

---

รับทำโปรเจค  เลข_EMS_ที่ส่งสินค้าแล้ว  Download  รายการสินค้า  ตะกร้าสินค้า  วิธีการสั่งซื้อ  แจ้งการชำระเงิน  บทความ